風管生產時連接技術工作注意事項！

發布人：http://m.lessonsfromyesterday.com   發布時間：2018-11-15 09:53:50

你知道風管生產時牢固密封性有哪些優勢嗎？風管連接技術工作注意事項有哪些嗎？風管生產時其連接要牢固密封性是很強的，下面就和大家分析一下該產品的性能，增加產品的可用性和競爭性。

Do you know the advantages of solid sealing when wind pipes are produced? Are there any matters needing attention in the connection of wind pipes? When air duct is manufactured, its connection must be firmly sealed. Here we will analyze the performance of the product and increase its usability and competitiveness.

風管在工業生產的地位不言而喻，很多人對風管的用途，風管材質等都有一定的了解，但是卻忽略了較為關鍵卻很容易被大家忽視的細節，風管生產時風管連接就是其中被忽略的要點之一，以下是詳細情況。

The position of duct in industrial production is self-evident, many people have a certain understanding of the use of duct, duct material, etc., but ignore the more critical but easily ignored details, duct connection is one of the neglected points in duct production, the following is the details.

1、因?yàn)轱L(fēng)管生產線廠家和施工不在同一個場地進行，因此在生產車間生產的風管生產線都是半成品。將半成品按照順序經過合理的編號后，然后再將其搬到施工場地再統一安裝。

1. Because the manufacturer and construction of the air duct production line are not carried out on the same site, the air duct production line produced in the production workshop is semi-finished products. After the semi-finished products are reasonably numbered in sequence, they are then moved to the construction site for unified installation.

2、一般來說，風管之間的連接都采用聯合角咬口的方式來進行，這樣在今后的使用中風管就具有良好的密封性。

2. Generally speaking, the connection between air ducts is carried out by means of joint angular bite, so that the air duct will have good sealing performance in the future.

3、對于支管和主管之間的連接，較好采用聯合咬口或反邊用拉釘與主管鉚接。在連接處較好用玻璃膠密封來防止漏風現象發生。

3. For the connection between branch pipe and main pipe, it is better to use joint bite or rivet with pull nail on the opposite side with main pipe. At the junction, it is best to use glass glue seal to prevent air leakage.

4、對于管法蘭與法蘭間，較好采用特制的TFD法蘭角，然后用榔頭將其敲入法蘭中再用螺栓連接。

4. For pipe flange and flange, it is better to use special TFD flange angle, and then hammer it into the flange and then bolt connection.

風管連接技術注意工作事項

Pay attention to matters relating to air duct connection technology

1、風管生產線廠家表示，一般對于玻璃風管來說，其連接采用的都是法蘭連接，而對于塑膠風管來說，采用焊接的方式比較多。

1. The manufacturer of air duct production line said that for glass duct, flange connection is generally used, while for plastic duct, welding method is used more.

2、為了讓風管的密封性效果不會在連接處出現問題，可以在每個分管的端口之間墊上襯墊。

2. In order to ensure that the sealing effect of the duct does not appear problems at the connection, a gasket can be padded between the ports of each branch.

3、如果風管口徑比較大，通常在工作的時候管道振動會發出很大的噪音。為了解決這一問題，風管需要進行再加固，這樣風管在使用的時候發出的噪音就沒有那么大。

3, if the diameter of the duct is relatively large, usually the pipe will vibrate very loudly when working. In order to solve this problem, the ducts need to be reinforced so that the noise generated by the ducts in use is not so great.

4、風管的密封效果除了在每段風管端口處放襯墊外，還可以借助板材的連接來改善。為了讓連接處密封性和牢固性更強，可以使用蜂蜜膠將縫隙粘合起來。

4. The sealing effect of air duct can be improved by the connection of sheet metal besides placing a gasket at the end of each section of air duct. In order to make the joints more sealed and strong, you can use honey glue to sew the gaps together.